Can you use 6 ohm and 8-ohm speakers together?

It is not a problem to combine 6 Ohm and 8 Ohm speakers; however, if the OP requires assistance and has 6 Ohm speakers as well as a 6-ohm option on the AV Receiver, it is preferable to select an 8 Ohm setting, just in case the AV Receiver heats up and causes the house to catch fire.

It is measured in Ohms, which is the amount of resistance that a device, such as a stereo speaker, will put up to impede the flow of electricity. The greater the ohm value, the greater the amount of power required to drive the speakers. Amplifiers and audio receivers are responsible for delivering the necessary ability to drive your speakers. Energy is measured in watts, which is converted to an ohms resistance by an amplifier or receiver.

For instance, 100 watts to 8 ohms is rated as 100 watts. It is possible to avoid overheating your equipment by using a few basic calculations when connecting sets of speakers with varying ohm ratings. This article includes the steps to follow when using speakers with different ohm together. You will also find answers to some of the frequently asked questions.

How to use an 8-ohm and a 6-ohm speaker together

Can you use 6 ohm and 8-ohm speakers togethe

Step 1

Turn each speaker around to check the ohm rating written on the speaker’s back before connecting it to the amplifier or receiver. For example, you might have a pair of amplifiers with an impedance of 4 ohms and an impedance of 8 ohms on each.

Step 2

Remove the speaker system or receiver from the speaker and look at the minimum ohm needs showing close to the speaker’s connections. An amp rated at 100w to a minimum impedance of 4 ohms, for example, can be used.

Step 3

Cut a wire section for each device and peel away a half-inch of the wire’s plastic coating from either end of the segment.

Step 4

In this scenario, the overall ohm for all woofer pairs would be 4+4(8) and 8+8, respectively (16). The soundbar (8 ohms) multiplied by the sound system B (16 ohms) equals 128 in the mixing computation. Following that, the overall omics as in two sound systems are split by 12. In this case, the approximation is 128/24 = 5.33 ohms. This is within the allowed range of your amplifier’s 4-ohm minimal level and can be securely connected.

Step 5

Step 5

Connect your speaker cables to the amplifier or receiver using the coloured cable for the positive pole and the other wire for the negative terminal. Connect the other end of each wire to a speaker in the same manner so that the cables do not cross.

Any amplifier should theoretically be capable of delivering some level of power to any speakers, independent of their impedance; however, how effectively this is accomplished is the topic at hand. It should be possible to power speakers with a nominal impedance of 6ohm with amplifiers that claim to be capable of doing so. Lower impedances may cause problems, but 6 ohms should be sufficient for most applications.

How a low impedance can result in a high-performance level

How a low impedance can result in a high-performance level

If you are using lower-ohm speakers with equipment that cannot support them, you may find yourself having to turn the amp up. The kit may be destroyed as a result. When a receiver or amplifier isn’t up to the task, a poorly matched pair of drivers and an inadequately matched pair of amplifiers may produce problems.

Any modern speaker may be connected to practically any current amplifier, and you’ll have more than sufficient volume to fill the living room with an entire music collection. The exact difference between a 4-ohm speaker and a 6-ohm or an 8-ohm speaker is a source of debate. Not much—just the low impedance can be a sign of how much fine-tuning the engineers accomplished when creating the speaker, and this is not always the case.

The impedance of the speaker changes depending on how high or low the audio frequency is pitched (or frequency). At 41 hertz, the impedance of the amplifier on a conventional bass guitar could be 10 ohms. It is possible to have an impedance as low as three ohms at 2,000 hertz. The impedance specification of a speaker is simply a rough average of several different figures.

Most stringent speaker designers equalize the impedance of their speakers to provide consistent sound quality over the whole acoustic range of their speakers. A speaker engineer might employ electrical circuits to smooth areas of high resistance, similar to how one might sand a piece of wood and remove the high ridges of grain that emerge in the wood. Despite their extensive use in high-end audio, 4-ohm speakers have remained mostly missing from mass-market audio due to the extra care and maintenance they necessitate.

Frequently Asked Questions:

  • How can one measure the speaker ohms?

Answer; Differentiate between positive and negative sides of the terminals on the speaker cone by looking at it. Connect the positive side of your multimeter with the red probe and the negative side with the black probe. Calculate the impedance using a multimeter and round the result up to the nearest decimal point. A 3-ohm speaker, for example, might be indicated by a 3-ohm multimeter.


In conclusion, Amplifier clipping is a problem because it takes a waveform that isn’t deformed and cuts off the top and bottom. This distorts by introducing high frequencies that were not there in the original transmission. When taken to its logical conclusion, the initial signal can be changed from a sine wave to a square wave. The square wave contains high frequencies that were not present in the original signal, posing a severe threat to the high frequency of the loudspeaker system (s).

Low impedance speakers necessitate the use of higher power amplifiers, which require more effort. It would have a lot to do with the amp’s power rating, to be honest. It’s not worth throwing away a perfectly excellent amplifier, and it shouldn’t make much of a difference in most cases. Some amplifiers perform worse when their rail power for output is switched to lower impedance speakers, and you can get better performance by leaving your amp set for 8-ohms using 6-ohm speakers.

Leave a Comment